Device.Backup.Running Config fails on WRT54GL v1.1
Hardware: Cisco WRT54GL v1.1 with DD-WRT firmware dd-wrt.v24_std_generic.bin. SNMP enabled on the router and I can successfully telnet into the router using PuTTY.CatTools Device Information: Device...
View ArticleWe are migrating from SNMPv2 to SNMPv3. When will SNMPv3 be supported?
Hi, We are migrating from SNMPv2 to SNMPv3. When will SNMPv3 be supported? We use SNMP within Cattools to get the "SNMP location", and "SNMP Contact" information from devices.
View ArticleDid not receive expected response to command: show running-config
I have a question, I have 2 Cisco WiSM (Cisco 6500 blade) that I am trying to use Cat tools to backup the config files on a regular schedule. I have run into the following error when trying to run the...
View ArticleBackup config.csv for a RuggedCom device
I am trying to find a way to schedule the backup of a ruggedcom RS900G using CatTools. We have a banner configured and once you log in, the device prompts you to press enter. I cant seem to find a...
View ArticleFortinet Fortigate Backups via TFTP
Hi I have managed to get a full back of a Fortigate firewall working using TFTP and I thought I would share how I did it with the community. We have a pair of Fortigates 3600C and we run multiple VDOMs...
View ArticleDoes anyone know how best to back up a Cisco WLC 2504?
Working with CatTools. The issue I have is when I hit the WLC with SSH, I get a username prompt first which is extraneous. I just hit enter to pass it, then a get the second username/password prompt...
View ArticleBackup Extreme Summit switches using TFTP commands
Hi, We have just installed some extreme switches and currentlyit is backing up using model X450-24X running the show configuration command.We are wanting to run the following below command and wondered...
View ArticleRuggedcom Rs900
Hi,I am trying to make a custom device for a Ruggedcom Rs900 swtich (ROS). The problem is - although I created a device variation for my device the Post_Login_Keystrokes are not executed.I just want to...
View ArticleEnable Mode Fails on Cisco router
Hi , I am new to Kiwi tools . I am not able to take the backup of my cisco router using Kiwi . I am getting the error message like "enable mode failed" . I have tried to capture the error but when...
View ArticleActivity Report.Version table fails with APC AP9630 UPS Network Management...
Hi!The Activity Report.Version table fails with the new APC UPS Network Management Card 2 model AP9630 (AOS 5.x). The error is Failed to determine device prompt anchor point - Most likely reason is...
View ArticleCattols 3.10 to FortiOS 5.2.5 or 5.4 doesn´t work
Hi, since we upgraded to FortiOS 5.2.5 or 5.4 Cattools gives us the error message "Failed to connect to XXX. Reason: No respone from remote host. Will try again."If we connect to it with Putty we get a...
View ArticlePROBLEM TO CONNECT TO HP PROCURVE 6120 XG SWITCH WITH CATTOOLS
Hi my friends, I am running Cattools version 3.10.0, now I am trying to backup the running configuration a HP Procurve 6120 XG switch. I have tried to enter some combinations of values under the...
View ArticleClik here to view.
Issue backing up Nexus 5000
Hi all, I'm implementing Cattools for a client to show the value in it (so they'll buy it).I can't get it to log into their Nexus 5010 switches (2).No matter what i do, the authentication ALWAYS fails,...
View ArticleConfiguring Cisco Nexus 7k in Kiwi Cat Tools
I've been able to use Kiwi Cat Tools to backup nearly all of our Cisco devices successfully. However, our Nexus 7k's do not seem to be working with Cat Tools. We use radius authentication and ssh to...
View ArticleClik here to view.
did not receive expected response to command: show configuration command -...
I am using generic router. here is the dubug set traffic-policy rate-control RATE-10Mbps bandwidth '10mbps'[27][m[13][10][13][27][K[27][?1l[27]>Myrouter@TB-B1-FW1:~$ (All output is correct till...
View ArticleHP Procurve - Compare Start Vs Run
I am trying to get CatTools to do Startup vs Run Configuration comparison on our HP procurve 2600, 5400, 2900, Etc Switches. I have managed to do a standard backup with the device set as...
View ArticleBacking up Mellanox SX1036
I get an error did not receive expected prompt when entering enable mode. Here is some log stuff <NEWSESSION CatTools 3.6.0 6/11/2013 1:22:43 PM><PROTOCOL=SSH2><DEVICE...
View ArticleDell m6220 - Did not receive VTY entry prompt from device after CR
Can not get CatTools to backup the configs on my Dell m6220 switches. Have read several existing posts but their resolves did not work. * have changed from Dell Switch CLI to Cisco.Switch.IOS -...
View ArticleBackup Config of Checkpoint Gateway
Hi Thwack community, this is my first discussion We are having some troubles with "Checkpoint Security Gateway" Devices. Because there is no suitable Device-Template for those devices i used the...
View ArticleMain script error: An object with the given name has already been added. on...
Hi all,Can somebody please help me here?Last couple of days, I am getting following error message for scheduled backup.Date stamp Device name Error...
View Article