Backup APC SmartUPS Network Management Card Config

November 2, 2010, 1:33 am

≫ Next: Problem to connect to HP Procurve 2530 switch with Cattools

≪ Previous: HP Procurve configuration backup using SSH problem

Hi!

Is there a chance that CatTools could retrieve the config.ini of a APC SmartUPS AP9617/AP9630 Network Management Card using FTP? It would be great if someone of the development team could have a look at it.

Here's a "capture" of a FTP session:

ftp> open 10.0.0.1
Connected to 10.0.0.1.
220 AP9617 Network Management Card AOS v3.7.3 FTP server ready.
User (10.0.0.1:(none)): admin
331 User name okay, need password.
Password:
230 User logged in, proceed.
ftp> bin
200 TYPE Command okay.
ftp> hash
Hash mark printing On ftp: (2048 bytes/hash mark) .
ftp> get config.ini
200 PORT Command okay.
150 File status okay; about to open data connection.
#######################226 Closing data connection.
ftp: 47311 bytes received in 15,25Seconds 3,10Kbytes/sec.
ftp> close
221 Thank you for using APC products!
ftp> quit

Regards, Leonardo

↧

Problem to connect to HP Procurve 2530 switch with Cattools

December 23, 2013, 10:39 pm

≫ Next: The Freeware edition of Kiwi CatTools v3.7 supports

≪ Previous: Backup APC SmartUPS Network Management Card Config

Hi my friends,

I am running Cattools version 3.6.0, now I am trying to backup the running configuration a HP Procurve 2530 switch. I have tried to enter some combinations of values under the "Passwords" and "Prompts" tab, but always prompted error messages. Can someone show me what value should I set under "Passwords" and "Prompts" tabs? Below I will show you how I telnet to this switch via command prompt. Thanks in advance!

From command prompt, I key in telnet 10.x.x.x, then press enter, then I see below page

I key in manager, and press enter, then I am prompted to enter password.

I enter password, and then press enter, I successfully enter privilege mode

↧

The Freeware edition of Kiwi CatTools v3.7 supports

March 22, 2012, 2:06 am

≫ Next: Does anyone know how best to back up a Cisco WLC 2504?

≪ Previous: Problem to connect to HP Procurve 2530 switch with Cattools

Hi,

I'm evaluating CatTools v3.7.
After the evaluation period is expired, I selected "Free mode".

Then I tryed to add a new device, CatTools displayed the following message.

================================================

Sorry, the Freeware edition is limited to 1 device.

================================================

I believe I can add up to 20 devices on Freeware edition.
http://www.kiwisyslog.com/kiwi-cattools-licensing/

The Freeware edition of Kiwi CatTools supports:
        - Up to 20 devices in the device database
        - Up to 20 scheduled activities
        - Up to 10 simultaneous TFTP sessions
        - Up to 5 client threads

Why cannot I add the device?

↧

Does anyone know how best to back up a Cisco WLC 2504?

June 17, 2014, 10:25 am

≫ Next: Backing up Alcatel OmniSwitch with CatTools

≪ Previous: The Freeware edition of Kiwi CatTools v3.7 supports

Working with CatTools.

The issue I have is when I hit the WLC with SSH, I get a username prompt first which is extraneous. I just hit enter to pass it, then a get the second username/password prompt which is when I enter my credentials. Works using putty, but I don't know how to get cat tools to work with it.

Or if there is any better way to capture a 2504.

↧

Backing up Alcatel OmniSwitch with CatTools

April 19, 2013, 2:33 am

≫ Next: Upgrading license

≪ Previous: Does anyone know how best to back up a Cisco WLC 2504?

HI guys,

I have been trying to backup up my OmniSwitches (6850 p48 variants) with CatTools.

The built in device is for omnistacks which doesn't work (Omniswitches don't have an enable mode) so I started to write my own template.

I can get CatTools to log in and dump the config, however only half the config is dumped.

Initially it appeared it was because CatTools was seeing the session prompt command in the config and flushed everything after it because of bCleanBuffer option in the SendCommandSingle() function.

I changed the GetConfig() function so that it when it calls the SendCommandSingle() function it is passing false to the bCleanBuffer to try and stop the above, however this only gave me a few extra lines of the config and it is still missing most of the config.

Now I am pretty much stuck!

Any pointers as to why this might be happening?

Edit: Ok, setting the bCleanBuffer helps (stops it clearing everything after the session prompt) but another part of the function s seeing it and then runs the exit command which is why I get a few more lines. Investigation

↧

Upgrading license

June 19, 2014, 3:39 am

≫ Next: HP Procurve configuration backup using SSH problem

≪ Previous: Backing up Alcatel OmniSwitch with CatTools

Hi,

We have active license to use KIWI CATTOOLS but it is for Version 3.4,

Is it possible to update KIWICATTOL to its latest version by carrying the same License that we are using for version 3.4.

Please reply

↧

HP Procurve configuration backup using SSH problem

September 10, 2009, 6:49 am

≫ Next: Issue backing up Nexus 5000

≪ Previous: Upgrading license

Hello,

We have an HP Procurve J4903A Switch 2824 and it is integrated with RADIUS Server for authentication.
We are using Cat Tools 3.4 demo version and tried to configure the switch for configuraton backup using Method SSH2.
And using Device.Backup.Running Config Type and SSH Username/Password are supplied. When Run the backup it shows the errors:
"Did not receive expected prompt when entering enable mode", and "Aborting: Unable to enter enable mode".

Do anybody faced this issue with SSH? Please help me to solve this problem.

Regards,

Achu

↧

Issue backing up Nexus 5000

February 20, 2012, 4:42 pm

≫ Next: Backup APC SmartUPS Network Management Card Config

≪ Previous: HP Procurve configuration backup using SSH problem

Hi all,

I'm implementing Cattools for a client to show the value in it (so they'll buy it).

I can't get it to log into their Nexus 5010 switches (2).

No matter what i do, the authentication ALWAYS fails, however i can log into the switches using putty with the same cred's.

Any ideas? Here are some debug's:

↧

Backup APC SmartUPS Network Management Card Config

November 2, 2010, 1:33 am

≫ Next: Capture Serial Number from Cisco Router

≪ Previous: Issue backing up Nexus 5000

Hi!

Here's a "capture" of a FTP session:

Regards, Leonardo

↧

Capture Serial Number from Cisco Router

March 10, 2009, 4:37 am

≫ Next: Error while unpacking program, code LP5. Please report to author.

≪ Previous: Backup APC SmartUPS Network Management Card Config

We have 50 remote offices with Cisco 1801's. I have the exciting job of establishing their serial numbers :-/

Can kiwi help. I guess the output I'm after comes from the 'show inventory' command. Or is there a MIB which can be installed into Orion which can be run to do the same job. The information i'm specifically after is serial number.

↧

Error while unpacking program, code LP5. Please report to author.

May 11, 2011, 1:57 am

≫ Next: Backing up Alcatel OmniSwitch with CatTools

≪ Previous: Capture Serial Number from Cisco Router

Kiwi Cattools is stopping after trying to execute it. Error windows pops up with message: "Error while unpacking program, code LP5. Please report to author."

Tried to unistall and reinstall the product (Kiwi CatTools 3.4.0) without success. CatTools has been running since years without any problems, until now. Probably some other recently (automatic) installed application or service is the cause, but I am not able to identify; I have installed nothing new for the last weeks.

Any help or advise is appreciated... thanks

↧

Backing up Alcatel OmniSwitch with CatTools

April 19, 2013, 2:33 am

≫ Next: having trouble copying the run config of a cisco 2960 cluster member, which is only accessible via the rcommand

≪ Previous: Error while unpacking program, code LP5. Please report to author.

HI guys,

I have been trying to backup up my OmniSwitches (6850 p48 variants) with CatTools.

The built in device is for omnistacks which doesn't work (Omniswitches don't have an enable mode) so I started to write my own template.

I can get CatTools to log in and dump the config, however only half the config is dumped.

Initially it appeared it was because CatTools was seeing the session prompt command in the config and flushed everything after it because of bCleanBuffer option in the SendCommandSingle() function.

Now I am pretty much stuck!

Any pointers as to why this might be happening?

↧

having trouble copying the run config of a cisco 2960 cluster member, which is only accessible via the rcommand

March 27, 2011, 11:30 pm

≫ Next: Problem to connect to HP Procurve 2530 switch with Cattools

≪ Previous: Backing up Alcatel OmniSwitch with CatTools

i have 2 cisco 2960's that are connected to each other via cluster. Now the only way to reach the second switch is by executing the command "rcommand 1," from the first switch. Now when i run CatTools, it copies the running config of the first switch, because i am able to telnet to it. However, it does not copy the running-config of the second member in the cluster, because i have to execute the command "rcommand1," in order to get inside the second switch. So i am stumped as to how to resolve this. Anyone have ideas? or run into the same problem?

↧

Problem to connect to HP Procurve 2530 switch with Cattools

December 23, 2013, 10:39 pm

≫ Next: Backing up F5 BIGIP UCS archive

≪ Previous: having trouble copying the run config of a cisco 2960 cluster member, which is only accessible via the rcommand

Hi my friends,

From command prompt, I key in telnet 10.x.x.x, then press enter, then I see below page

I key in manager, and press enter, then I am prompted to enter password.

I enter password, and then press enter, I successfully enter privilege mode

↧

Backing up F5 BIGIP UCS archive

April 12, 2010, 2:46 am

≫ Next: TFTP server backup config.txt for Cisco 2960s

≪ Previous: Problem to connect to HP Procurve 2530 switch with Cattools

Does anybody know if there is a way to backup the UCS archive on the BIGIP's, I think the current template in CatTools only backs up the config file. You really need the UCS archive to be able to restore devices properly.

Many thanks

Mark

↧

TFTP server backup config.txt for Cisco 2960s

October 25, 2012, 9:42 am

≫ Next: Reason (30012) Protocol version mismatch error.. Giving up after 3 connection attempts"

≪ Previous: Backing up F5 BIGIP UCS archive

Hi,

I'm new to using CAT tools Enterprise v. 3.7. I have a Cisco 2960S switch that I need to backup the config on it via TFTP. Curious, if I run the script "Device.Backup.RunningConfig", will it cause any interruption to service on the switch? Also, once the config is backed up, how do I take that config and copy to another switch?

↧

Reason (30012) Protocol version mismatch error.. Giving up after 3 connection attempts"

June 28, 2011, 4:29 am

≫ Next: Connect failed:30002:Please set your login for selected protocol.

≪ Previous: TFTP server backup config.txt for Cisco 2960s

Dear Sir

I am new to KIWIcat tool, first time I have installed this tool to integarate with cisco asa for backup purpose. We manage around 100 cisco asa firewall and used to take manual backup. So we want to convert this process automatically with the help of kiwicat tool. However I am getting error message while take backup through tool which is listed below.

Reason (30012) Protocol version mismatch error.. Giving up after 3 connection attempts"

Could you please let me know if I have wrongly configured this or having this error due to any other reason.

Version of tool is 3.6.0 which I believe is latest one.

Please let me know if you require any other information to dig out the problem.

Thanks in advance

↧

Connect failed:30002:Please set your login for selected protocol.

August 12, 2011, 3:40 am

≫ Next: error with SG300 and Device.Backup.Running.Config

≪ Previous: Reason (30012) Protocol version mismatch error.. Giving up after 3 connection attempts"

Hi,

I am trying to backup my cisco 3925 router using kiwi cattools. Till yesterday it was working with telnet. I have disabled telnet and enabled SSH. I am able to connect to the router using the credentials used in the device properties, but when i try to backup using the kiwi software i am getting the below error. tried changing the SSH ver to 1 with no luck.

Error: Connect failed:30002:Please set your login for selected protocol.

Thanks,

Sridhar

↧