Hi,
im trying to save my running configurations to a network drive. It seems once i installed cattools as a service, it did not work. However, It did work when i installed catTools as an application. Does anyone know what i can do? i am running windows 2003
Unable to create destination file: Z:\DOCS\Configuration Files\backup configurations_all_cores(RECENT)\Config.Current.Running.test.txt
Hi,
I'm using Cattools 3.9 over Windows 2008 R2.
Problem is that all activities get stuck in the same point: after SSH fingerprint debug message (see attachment). Telnet is working fine.
SSH client is working fine because if i use Telnet/SSH to device it opens ssh client (putty), and i cant connect to the device without problem.
I had cattools 3.6 over windows 2003 and this were working fine. I have tried even exporting devices and activities and doesn't work either.
Thank you in advance
Hi,
I'm stuck with Cat Tools and HP ProCurve. I want to change the password but that does not work. CLI from HP ProCurve demands to Verify your new password. Cat Tools can not handle this.
Does anyone have an idea how to solve this?
I am receiving the following message from a newly installed Riverbed Router. Any ideas?
2013-10-05 23:15:17 2-Warning 6 Riverbed-Router Failed to connect to Riverbed-Router. Reason: (30044) No available encryption algorithms match with the server.. Will try again.
Hi my friends,
I am running Cattools version 3.6.0, now I am trying to backup the running configuration a HP Procurve 2530 switch. I have tried to enter some combinations of values under the "Passwords" and "Prompts" tab, but always prompted error messages. Can someone show me what value should I set under "Passwords" and "Prompts" tabs? Below I will show you how I telnet to this switch via command prompt. Thanks in advance!
From command prompt, I key in telnet 10.x.x.x, then press enter, then I see below page
I key in manager, and press enter, then I am prompted to enter password.
I enter password, and then press enter, I successfully enter privilege mode
Cattools 3.10
I'm trying to back up a Dell DR4100 using Telnet, and after changing Username prompt: to login: it will connect ok, but it fails to back up, with error message Aborting: Unable to enter enable mode.
There doesn't appear to be an enable mode for this device. Can I bypass this bit?
Thanks,
Jenny
Linksys SFE2000P issue
To access the CLI and modify the configuration or any other command, the only method is to connect using a screen menu then to enter CTRL-Z
SSH to switch
First : login as: --> I can enter what I want
Then a menu will display
Username : --> I enter the username the I need to enter <TAB> to move to
Password : --> I enter the password and finished by <Enter>
The main menu appears
See détails in the attached file.
Hi,
since we upgraded to FortiOS 5.2.5 or 5.4 Cattools gives us the error message "Failed to connect to XXX. Reason: No respone from remote host. Will try again."
If we connect to it with Putty we get a session.
Have debugged the SSH from FortiOS but no error messages is shown.
The debug in Cattools doesn´t give any errors either:
<NEWSESSION CatTools 3.10.0 2016-01-15 08:41:31>
<PROTOCOL=SSH2>
<DEVICE TYPE=Fortinet.FortiOS.General>
<ACTIVITY TYPE=Device.Backup.Running Config>
<ACTIVITY SCRIPT=D:\Program Files (x86)\CatTools3\Scripts\Client.Device.Backup.Running Config.txt>
<USERS NAME FOR DEVICE=nbo-osd2fw01>
<D 13:48:31>
<SCRIPT VALUES>
<HOSTNAME="">
<PROMPT VTY="">
<PROMPT ENABLE="">
<PROMPT CONFIG="">
We have tried all different SSH ciphers but with the same result. When we save the ciphers we can see that it sends it to the FortiOS and that it accept it.
Any ideas?
Robin
Hi all,
I'm implementing Cattools for a client to show the value in it (so they'll buy it).
I can't get it to log into their Nexus 5010 switches (2).
No matter what i do, the authentication ALWAYS fails, however i can log into the switches using putty with the same cred's.
Any ideas? Here are some debug's:
I have some connection problems with some of my devices in my network. I have about 50 Riverbed 250L cashe boxes that I routinely back up each night with a kiwi script.
Lately I have been getting errors such as:
Connect failed:(30044) No available encryption algorithms match with the server.
I am sure I have my encryption set up right, as I have only about a 15% failure and they are all set up the same.
Any suggestion I could check into?
JT
I am attempting to configure Cat Tools to backup some of our Dell PowerConnect 5548s running-configs over SSH, however I am running into problems when initiating the SSH session. Since the Dell SSH on the appliance is built on top of Telnet, it prompts for a useless field "Login as:" before asking for the local username and password. This first field has no effect on whether or not you can authenticate to the device.
I cannot find a way to put in a carriage return or line-feed command to make the session continue to the "Username: " prompt.
I apologize for my sentence structure on this post.
Cheers,
Stefan
Hi
I am new to Cattools
I am trying to backup configuration on my HP ProCurve switchs (mainly 2510 and 2626)
I got "Did not receive VTY entry prompt from HP" when trying to do Device.Backup.Running.Config.
The switch is default configured with no password.
Debug log
--------------------
<NEWSESSION CatTools 3.5.0 10-11-2010 13:39:14>
<PROTOCOL=Telnet>
<DEVICE TYPE=HP.Switch.2500>
<ACTIVITY TYPE=Device.Backup.Running Config>
<ACTIVITY SCRIPT=C:\Program Files (x86)\CatTools3\Scripts\Client.Device.Backup.Running Config.txt>
<USERS NAME FOR DEVICE=SW12>
<C OK 13:39:14><R-13:39:14>[27][2J[27][?7l[27][3;23r[27][?6l[27][1;1H[27][?25l[27][1;1HProCurve J9279A Switch 2510G-24[13][10][13]Software revision Y.11.16[13][10][13][13][10][13]Copyright (C) 1991-2009 Hewlett-Packard Co. All Rights Reserved.[10][13][10][13] RESTRICTED RIGHTS LEGEND[10][13][10][13] Use, duplication, or disclosure by the Government is subject to restrictions[10][13] as set forth in subdivision (b) (3) (ii) of the Rights in Technical Data and[10][13] Computer Software clause at 52.227-7013.[10][13][10][13] HEWLETT-PACKARD COMPANY, 3000 Hanover St., Palo Alto, CA 94303[10][13][10][13]We'd like to keep you up to date about:[10][13] * Software feature updates[10][13] * New product announcements[10][13] * Special events[10][13][10][13]Please register your products now at: www.ProCurve.com[10][13][10][13][10][13][27][1;24r[27][1;1H
================================================================================
WFMDRetVal=1 Waiting for: "ress any key to continue"
WFMDRetVal=2 Waiting for: "Password required, but none set"
WFMDRetVal=3 Waiting for: "Password:"
WFMDRetVal=4 Waiting for: "Username:"
WFMDBuffer="[27][2j[27][?7l[27][3;23r[27][?6l[27][1;1h[27][?25l[27][1;1hprocurve j9279a switch 2510g-24[13][10][13]software revision y.11.16[13][10][13][13][10][13]copyright (c) 1991-2009 hewlett-packard co. all rights reserved.[10][13][10][13] restricted rights legend[10][13][10][13] use, duplication, or disclosure by the government is subject to restrictions[10][13] as set forth in subdivision (b) (3) (ii) of the rights in technical data and[10][13] computer software clause at 52.227-7013.[10][13][10][13] hewlett-packard company, 3000 hanover st., palo alto, ca 94303[10][13][10][13]we'd like to keep you up to date about:[10][13] * software feature updates[10][13] * new product announcements[10][13] * special events[10][13][10][13]please register your products now at: www.procurve.com[10][13][10][13][10][13][27][1;24r[27][1;1h"
================================================================================
Hi,
Is there a way to export my node and SNMP credentials from NPM into CatTools, we have about 400 nodes in NPM and I don't want to enter them all into CatTools manually!
I see it has an import option but don't know how to get the info out of NPM in the right format.
thanks,
Steve.
Hi,
I have an existing support case open with SolarWinds support for this issue 1066183.
I just want to find out from the community whether anyone had encountered this issue and have a solution.
My Kiwi Cattools show its unlicensed since yesterday even though it was licensed correctly and working properly for past few years.
SolarWinds License Manager show a message Licensing System Repair: There is a problem with your licensing system. Contact SolarWinds technical support.
SolarWinds support reset our license key and ask me to reactivate it but the activation fail and following log were observed in SolarWinds License Manager log.
I'm still waiting for SolarWinds technical support get back to me on how to resolve this issue.
2016-10-19 09:27:04,770 [1] INFO List licenses - Decrypting store document
2016-10-19 09:27:04,785 [1] INFO List licenses - 1 licences found
2016-10-19 09:27:04,785 [1] INFO List licenses - Found license - Name: KiwiCatTools; Version: 3; Type: Commercial, ActivationKey: XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX, MaintenanceEndDate: 5/21/2017 12:00:00 AM, SWID: XXXXXXXXX, #Features: 4, Node Locking Data: [XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX]
2016-10-19 09:27:04,785 [1] INFO List licenses - Using Licensing Framework to obtain license for KiwiCatTools / 3 / Commercial
2016-10-19 09:27:04,801 [1] ERROR SolarWinds.Licensing.Framework.Diagnostic.Logger - License store exception
SolarWinds.Licensing.Framework.Store.LicenseStoreException: Exception of type 'SolarWinds.Licensing.Framework.Store.LicenseStoreException' was thrown.
at SolarWinds.Licensing.Framework.Store.LicenseStore.RetrieveLicensesInternal(String appName, Int32 licenseVersion, LicenseType type)
2016-10-19 09:27:04,801 [1] ERROR SolarWinds.Licensing.Framework.Diagnostic.Logger - License error
SolarWinds.Licensing.Framework.ProductLicenseNotFoundException: A license for product KiwiCatTools, version 3, could not be retrieved.
at SolarWinds.Licensing.Framework.LicenseManager.GetLicenses(String appName, Int32 licenseVersion, LicenseType licenseType)
2016-10-19 09:27:04,801 [1] ERROR List licenses - Exception occurred when trying to obtain license for KiwiCatTools / 3 / Commercial
SolarWinds.Licensing.Framework.SolarWindsLicensingException: A license for product KiwiCatTools, version 3, could not be retrieved. ---> SolarWinds.Licensing.Framework.ProductLicenseNotFoundException: A license for product KiwiCatTools, version 3, could not be retrieved.
at SolarWinds.Licensing.Framework.LicenseManager.GetLicenses(String appName, Int32 licenseVersion, LicenseType licenseType)
--- End of inner exception stack trace ---
at SolarWinds.Licensing.Framework.LicenseManager.GetLicenses(String appName, Int32 licenseVersion, LicenseType licenseType)
at SolarWinds.Licensing.Framework.LicenseManager.GetLicense(String appName, Int32 licenseVersion, LicenseType licenseType)
at SolarWinds.Licensing.Analysis.TestRun.ListLicensesTestRun.Run(TestRunResults previousResults)
2016-10-19 09:27:04,801 [1] INFO SolarWinds.Licensing.Analysis.LicenseStoreHelper - Creating formatter
2016-10-19 09:27:04,817 [1] INFO SolarWinds.Licensing.Analysis.LicenseStoreHelper - License store instance was created successfully
2016-10-19 09:27:04,817 [1] INFO List licenses - Serial number for product KiwiCatTools / 3 / Commercial: [XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX]
2016-10-19 09:27:04,817 [1] INFO List licenses - Trying to get license information from registry for product KiwiCatTools / 3 / Commercial
2016-10-19 09:27:04,817 [1] INFO List licenses - Days left for product KiwiCatTools / 3 / Commercial: 2916049
2016-10-19 09:27:04,817 [1] INFO List licenses - Test List licenses result: Failure
2016-10-19 09:27:07,145 [1] ERROR SolarWinds.Licensing.Framework.Diagnostic.Logger - License store exception
SolarWinds.Licensing.Framework.Store.LicenseStoreException: Exception of type 'SolarWinds.Licensing.Framework.Store.LicenseStoreException' was thrown.
at SolarWinds.Licensing.Framework.Store.LicenseStore.RetrieveLicenses()
Hello everyone, I need some help. I have two errors that I'm having a issue with. Cattools sends me a errors in a email saying some of the back ups have failed.
Error 1: Reason: (10060) The current connection has timed out.. Giving up after 3 connection attempts.
Error 2: Reason: (10061) The requested connection has been refused by the remote host.. Giving up after 3 connection attempts.
I appreciate your help.
Thank you.
Hello,
Does anyone know how to fix the below error:
(30016) Invalid username or password reported by server, or bad private key
Much appreciated!!!
Hi
Has anyone been able to get an automated backup of the 200 series small business switches. I noted that there seems to be scripts for the SG300 but not the SG200.
Is there a reason that the SG200's don't work with Cattools?
Thanks
Matt
Linksys SFE2000P issue
To access the CLI and modify the configuration or any other command, the only method is to connect using a screen menu then to enter CTRL-Z
SSH to switch
First : login as: --> I can enter what I want
Then a menu will display
Username : --> I enter the username the I need to enter <TAB> to move to
Password : --> I enter the password and finished by <Enter>
The main menu appears
See détails in the attached file.
Hi!
I'm trying to backup the config of our new HP (H3C) Switches (5120, 5800, 10500). The script I created out of the Custom.Template is not working. The prompt of the switches is "<SWITCHNAME>", not "SWITCHNAME>" as in Ciscos IOS. So the script returns the error "Did not receive expected prompt when entering Enable mode".
Has anybody managed to create a script that works with the HP H3C switches?
Regards, lls71