Quantcast
Channel: THWACK: Popular Discussions - Kiwi CatTools
Viewing all 21331 articles
Browse latest View live
↧

Did not receive expected response to command: show running-config

September 1, 2010, 3:31 am
$
0
0

I have a question, I have 2 Cisco WiSM  (Cisco 6500 blade) that I am trying to use Cat tools to backup the config files on a regular schedule. I have run into the following error when trying to run the activity:  "Did not receive expected response to command: configshow" and then Cat tools disconnects from the switch. I used telnet to issue the show running-config command and what I noticed is right after the show running-config command is issued the switch prompts with: "Press Enter to continue or <CTRL-Z> to abort"  or "--More-- or (q)uit " and sits there until there is user intervension. How can I automate the CR to continue command so I can use Cattools to pull the configuration of these switches? Any help would be greatly appreciated.

Thanks

↧
Search

Workaround for Netgear devices and device.backup.running.config

March 17, 2016, 1:23 pm
$
0
0

Anyone have either a custom activity, device or script that will allow Netgear devices to backup and pass a compare run while ignoring the commented out lines that start with '!'?

 

Netgear time stamps their configs so they always show as changed.  Back reading the forums I see that the variations function was due for Netgear devices at some point but it is not in the current version.

 

I've tried working with Generic devices but I'm getting errors with what looks like it trying to set VTY functions.

↧
↧

Cattols 3.10 to FortiOS 5.2.5 or 5.4 doesn´t work

January 14, 2016, 11:47 pm
$
0
0

Hi,

 

since we upgraded to FortiOS 5.2.5 or 5.4 Cattools gives us the error message "Failed to connect to XXX. Reason: No respone from remote host. Will try again."

If we connect to it with Putty we get a session.

 

Have debugged the SSH from FortiOS but no error messages is shown.

 

The debug in Cattools doesn´t give any errors either:

<NEWSESSION CatTools 3.10.0 2016-01-15 08:41:31>

<PROTOCOL=SSH2>

<DEVICE TYPE=Fortinet.FortiOS.General>

<ACTIVITY TYPE=Device.Backup.Running Config>

<ACTIVITY SCRIPT=D:\Program Files (x86)\CatTools3\Scripts\Client.Device.Backup.Running Config.txt>

<USERS NAME FOR DEVICE=nbo-osd2fw01>

<D 13:48:31>

<SCRIPT VALUES>

<HOSTNAME="">

<PROMPT VTY="">

<PROMPT ENABLE="">

<PROMPT CONFIG="">

 

We have tried all different SSH ciphers but with the same result. When we save the ciphers we can see that it sends it to the FortiOS and that it accept it.

 

Any ideas?

 

Robin

↧

SNMP V3 for Cattool

April 29, 2013, 11:00 pm
$
0
0

Hi All,

 

Whether Cattool V3.6 will support SNMP v3? If yes, Please let me know how to set up SNMP V3 in cattools.

↧

How can I configure Cat Tools to connect to Dell SSH?

April 22, 2014, 5:04 pm
$
0
0

I am attempting to configure Cat Tools to backup some of our Dell PowerConnect 5548s running-configs over SSH, however I am running into problems when initiating the SSH session. Since the Dell SSH on the appliance is built on top of Telnet, it prompts for a useless field "Login as:" before asking for the local username and password. This first field has no effect on whether or not you can authenticate to the device.

I cannot find a way to put in a carriage return or line-feed command to make the session continue to the "Username: " prompt.

 

I apologize for my sentence structure on this post.

 

Cheers,

Stefan

↧
↧

Reason (30012) Protocol version mismatch error.. Giving up after 3 connection attempts"

June 28, 2011, 4:29 am
$
0
0

Dear Sir 


 


I am new to KIWIcat tool, first time I have installed this tool to integarate with cisco asa for backup purpose. We manage around 100 cisco asa firewall and used to take manual backup. So we want to convert this process automatically with the help of kiwicat tool. However I am getting error message while take backup through tool which is listed below.


 


Reason (30012) Protocol version mismatch error.. Giving up after 3 connection attempts"


 


 


 


Could you please let me know if I have wrongly configured this or having this error due to any other reason.


 


Version of tool is 3.6.0 which I believe is latest one.


 


Please let me know if you require any other information to dig out the problem.


 


Thanks in advance

↧

Change Password for Hirschmann RS20 Switch

July 28, 2016, 7:52 am
$
0
0

I'm trying to write a script to change password's for Hirschmann RS20 Switch.

 

Debug:

<W-16:03:06>users passwd user[13]

<R-16:03:06>u

<R-16:03:06>sers passwd user[13][10][13][10]Enter old password:

<W-16:03:06>public[13]

<R-16:03:06>*

<R-16:03:06>**[13][10][13][10]Incorrect Password![13][10][13][10](egvko1swvis6) (Config)#

 

.... but the password is right.

 

Script:

     ReDim rgMult(5)

   

    rgMult(1) = "Enter old password:"

    rgMult(2) = "Enter new password:"

    rgMult(3) = "Confirm new Password:"

    rgMult(4) = "... irgendwas"

    rgMult(5) = "Incorrect Password!"

   

    cl.Log 4, "SendData '" & sCmd & "'"

    cl.SendData sCmd & vbCr

   

    iRetValPWD = cl.WaitForMultData(rgMult, , COMMAND_TIMEOUT)

    cl.Log 4, "Buffer '" & cl.RxBuffer & "'"

   

    Select Case iRetValPWD

     Case 1, 2, 3, 4

           ' Password accepted - a valid device prompt was received back

           iNumSuccess = iNumSuccess + 1

           iChangePWD = iChangePWD + 1

           cl.Log 4, "SendData ok"

     Case 5

           cl.Log 4, "Incorrect Password!"

           SendCommandsMultiple = False

           Exit Do

     Case Else

           ' Unexpected response received back from device

           cl.Log 4, "Did not receive expected response after sending password"

           iNumErrors = iNumErrors + 1

    End Select

    cl.FlushRxBuffer

↧

Connect failed:(-32534) Disconnect : Protocol error

July 28, 2016, 12:05 am
$
0
0

Hi,

 

I'm trying to run commands on Redback.router but i get this error :

 

Connect failed:(-32534) Disconnect : Protocol error

 

I use SSH2 Method and when i click Telnet/SSH from the device, it open the connection corectly with Secure-CRT (with SSH2..)

 

I'm running 3.10 version of the cattools.

 

do you know what could be the problem ?

 

thanks

↧
Search

Fortigate With Vdom backup is not happening

March 31, 2010, 3:50 am
$
0
0

Hi All ,

 

I am not able to take the backup of Fortigate  which has configured on VDOM environment .

Some Fortigate's I am able to take but Vdom configuration's are missing from the Backup .

Did any one faced this issues and what was the solutions you found on Kiwi Cat tools

 

Please help thanks in advance

 

Regards

Vineeth

↧
↧

Doc, KB and Getting Started

June 19, 2013, 4:10 am
↧

General HP Switch Setup Help

June 27, 2016, 9:28 am
$
0
0

Good afternoon,

 

I just grabbed the latest version of Cattools (3.11) and I'm trying to setup a few devices but I'm having some trouble.

 

The first device is a HP4204v1 (J8770A) which states it failed to determine hostname - no CR or LF

 

The second is HP A5120-48G-POE

I step through both device connections through putty and tr to mirror the prompts as best I can through the variations but no success on either one.

 

Any help for a newbie is appreciated.

 

 

Thanks,

↧

Cattols 3.10 to FortiOS 5.2.5 or 5.4 doesn´t work

January 14, 2016, 11:47 pm
$
0
0

Hi,

 

since we upgraded to FortiOS 5.2.5 or 5.4 Cattools gives us the error message "Failed to connect to XXX. Reason: No respone from remote host. Will try again."

If we connect to it with Putty we get a session.

 

Have debugged the SSH from FortiOS but no error messages is shown.

 

The debug in Cattools doesn´t give any errors either:

<NEWSESSION CatTools 3.10.0 2016-01-15 08:41:31>

<PROTOCOL=SSH2>

<DEVICE TYPE=Fortinet.FortiOS.General>

<ACTIVITY TYPE=Device.Backup.Running Config>

<ACTIVITY SCRIPT=D:\Program Files (x86)\CatTools3\Scripts\Client.Device.Backup.Running Config.txt>

<USERS NAME FOR DEVICE=nbo-osd2fw01>

<D 13:48:31>

<SCRIPT VALUES>

<HOSTNAME="">

<PROMPT VTY="">

<PROMPT ENABLE="">

<PROMPT CONFIG="">

 

We have tried all different SSH ciphers but with the same result. When we save the ciphers we can see that it sends it to the FortiOS and that it accept it.

 

Any ideas?

 

Robin

↧

Script for HP/H3C Switches

September 26, 2012, 12:33 am
$
0
0

Hi!

 

I'm trying to backup the config of our new HP (H3C) Switches (5120, 5800, 10500). The script I created out of the Custom.Template is not working. The prompt of the switches is "<SWITCHNAME>", not "SWITCHNAME>" as in Ciscos IOS. So the script returns the error "Did not receive expected prompt when entering Enable mode".

Has anybody managed to create a script that works with the HP H3C switches?

 

Regards, lls71

↧
↧

Can CatTools backup configs for Brocade switches?

July 24, 2014, 8:35 am
$
0
0

I have used CatTools in the past to backup Cisco switch/router configs and I'd like to use it to backup Brocade ICX and FCX switch configs.  It looks likes the software supports "backup running config" but not "backup config TFTP".  I don't understand the differences between the two categories.  Can someone explain?

↧

Backup HP V1910 (Legacy 3Com 2928) switch

February 1, 2012, 7:18 am
$
0
0

I am trying to backup this switch using the Device.CLI.Send activity.  Here is what I am trying to send:

Login authentication　

Username:xxxx
Password:
<Raben Tire IT Switch>_cmdline-mode on
All commands can be displayed and executed. Continue? [Y/N]y

 

Please input password:******
Warning: Now you enter an all-command mode for developer's testing, some commands may affect operation by wrong use, please carefully use it with our engineer's direction.
<Raben Tire IT Switch>backup startup-configuration to 10.21.1.13
Backup next startup-configuration file to 10.21.1.13, please wait...
finished!
<Raben Tire IT Switch>quit

I get to the input of the password and get a syntax error.  Since I get a syntax error there, the rest of the script never runs, it also gets a syntax error.  How do I input a password at that point?

Thanks,
Jeff

 

 

↧
Search

Problem to connect to HP Procurve 2530 switch with Cattools

December 23, 2013, 10:39 pm
$
0
0

Hi my friends,

 

I am running Cattools version 3.6.0, now I am trying to backup the running configuration a HP Procurve 2530 switch. I have tried to enter some combinations of values under the "Passwords" and "Prompts" tab, but always prompted error messages. Can someone show me what value should I set under "Passwords" and "Prompts" tabs?  Below I will show you how I telnet to this switch via command prompt. Thanks in advance!

 

4.jpg

5.png

 

From command prompt, I key in  telnet 10.x.x.x, then press enter, then I see below page

1.jpg

I key in manager, and press enter, then I am prompted to enter password.

2.jpg

 

I enter password, and then press enter, I successfully enter privilege mode

3.jpg

↧

Invalid username or password - HP 6120 XG

August 2, 2016, 8:38 am
$
0
0

Hi  there,

 

I am running Cat Tools 3.3.17 and trying to backup all my device configs to one server.

 

I am having an issue with 2 HP switches - I receive a

Failed to connect to 172.x.x.x
  Reason: (30016) Invalid username or password reported by server, or bad
  private key.. Giving up after 3 connection attempts.

 

I am not too familiar with setting the device information - password, manager password etc. I have it for Direct connect via SSH2

 

Any help would be grateful!

 

G

↧
↧

HP Comware 7 Switches

June 2, 2016, 8:55 am
$
0
0

I have been using CatTools successfully with Cisco and HP Procurve switches for some time now, but I can't get the software to successfully talk to a new Comware switch. Looking at the debug logs it looks like it isn't coping with the default Comware prompt format e.g. <sysname> or [sysname] for user or system view respectively. Any idea what I need to do to get it to work?

 

Thanks

 

iain

 

ps I have logged a call with SolarWinds but this is proving to be a soul destroying process. The case is flagged as not started after two days, I've left answer phone messages to no avail and listened to muzak for far too long.

↧

No available encryption algorithm

October 7, 2013, 8:43 am
$
0
0

I am receiving the following message from a newly installed Riverbed Router.  Any ideas?

 

2013-10-05 23:15:17 2-Warning 6 Riverbed-Router Failed to connect to Riverbed-Router. Reason: (30044) No available encryption algorithms match with the server.. Will try again.

↧

HP Procurve configuration backup using SSH problem

September 10, 2009, 6:49 am
$
0
0

Hello,

We have an HP Procurve J4903A Switch 2824 and it is integrated with RADIUS Server for authentication.
We are using Cat Tools 3.4 demo version and tried to configure the switch for configuraton backup using Method SSH2.
And using Device.Backup.Running Config  Type and SSH Username/Password are supplied. When Run the backup it shows the errors:
"Did not receive expected prompt when entering enable mode", and "Aborting: Unable to enter enable mode".

Do anybody faced this issue with SSH? Please help me to solve this problem.

Regards,

Achu

↧
Viewing all 21331 articles
Browse latest View live
Search
<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>