TFTP server backup config.txt for Cisco 2960s
Hi,I'm new to using CAT tools Enterprise v. 3.7. I have a Cisco 2960S switch that I need to backup the config on it via TFTP. Curious, if I run the script "Device.Backup.RunningConfig", will it cause...
View ArticleScheduling timer not starting on restart
Hi,I am having trouble get the activity scheduling time to start on machine boot.I have Cattools running as a service and that starts fine if the machine is rebooted.However the scheduling timer...
View ArticleF5.BigIP.TMSH Changes Pending
Whenever I use the F5.BigIP.TMSH Device Type and have CatTools login into a Device I end up with a (Changes Pending) when the device was (In Sync) before. I thought maybe it had something to do with...
View Article"Did not receive VTY entry prompt from device" in Dell 6224P switches
Is there anyone help me to solve below porblem??I am trying to backup configuration on my Dell 6224P switchesI got "Did not receive VTY entry prompt from device" when trying to do...
View ArticleDid not receive expected response to conf t command!
Hi again! As you requested, I've made a new theme with my question. What kind of diagnostics you need from me?I have the same question as flexible, I have 2 Cisco IOS switches 2960 (first firmware...
View ArticleClik here to view.
Backing up Alcatel OmniSwitch with CatTools
HI guys, I have been trying to backup up my OmniSwitches (6850 p48 variants) with CatTools. The built in device is for omnistacks which doesn't work (Omniswitches don't have an enable mode) so I...
View ArticleDid not receive VTY entry prompt from HP
HiI am new to CattoolsI am trying to backup configuration on my HP ProCurve switchs (mainly 2510 and 2626)I got "Did not receive VTY entry prompt from HP" when trying to do...
View ArticleBackup of Cisco SF-300 ( small bussiness switch )
We´re not able to backup the config of those SF-300 switches, it is always ends up with error message "did not received command prompt after connecting via SSH" , probably because it´s not an IOS based...
View Articlecrossbeam backup
Hi There, I am trying to backup config for crossbeam x-series using kiwi Cattools but its popping up with an error saying "Did not receive expected response after sending password"any idea whats the...
View ArticleTFTP server backup config.txt for Cisco 2960s
Hi,I'm new to using CAT tools Enterprise v. 3.7. I have a Cisco 2960S switch that I need to backup the config on it via TFTP. Curious, if I run the script "Device.Backup.RunningConfig", will it cause...
View ArticleHP Procurve configuration backup using SSH problem
Hello,We have an HP Procurve J4903A Switch 2824 and it is integrated with RADIUS Server for authentication.We are using Cat Tools 3.4 demo version and tried to configure the switch for configuraton...
View ArticleLicensing error
Hi guys, When I try and run cattools I get this error: "you have too many copies of this program already running on your system or network. you are licensed for only 1 copy/copies at a time" The...
View ArticleCatTools Daily Device Backup on Cisco ASA: Saves from bannner down, misses...
When upgrading to CatTools 3.7, we started noticing the backup config task only captures from the banner downwards, missing the ASA version info, interface, hostname, etc. Fixed via utilizing the...
View ArticleBackup HP V1910 (Legacy 3Com 2928) switch
I am trying to backup this switch using the Device.CLI.Send activity. Here is what I am trying to send:Login authentication Username:xxxxPassword:<Raben Tire IT Switch>_cmdline-mode onAll...
View ArticleDid not receive expected response to command: show running-config
I have a question, I have 2 Cisco WiSM (Cisco 6500 blade) that I am trying to use Cat tools to backup the config files on a regular schedule. I have run into the following error when trying to run the...
View ArticleNew setup using CISCO ACS
Help, Trying to test the CatTools to backup a Cisco 2811 router and not sure how to set it up, The router has SNMP community strings and Cisco Secure Access Control Server (ACS) which uses a RSA. What...
View Articleget config command stops at --- more --- paging prompt
Hey guys,we have the following problem when running Kiwi Cat tool's Device.Backup.Running Config with the command "get conf" on a Juniper Netscreen Firewall:It always stops at the end of a page...
View ArticleNortel switch BS 450 and BS 470
Hi!Is there a mean to backup config from Nortel BS450 and BS470? I don't know the fields to fill for these equipments (Enable password? AAA Password?) and what is the prompt? (Enter Password: ?) I've...
View ArticleSupported Device - Works? Options?
I have just one switch that i need to backup, its a HP Procurve 5412zl. I notice when i add a device and it says vendor i put in HP, Device Type (Hp Switch 2500 * Only Option), then my only options are...
View ArticleDetect changes with Device.CLI.Send commands
Hi, I would like to know how to detect configuration changes with this kind of activity : Device.CLI.Send commands.I have to use this activity for backup made by TFTP or FTP. So, at this time, all my...
View Article