Clik here to view.
Problem to connect to HP Procurve 2530 switch with Cattools
Hi my friends, I am running Cattools version 3.6.0, now I am trying to backup the running configuration a HP Procurve 2530 switch. I have tried to enter some combinations of values under the...
View ArticleUnable to run an ARP report against a Cisco Nexus with KIWI CatTools 3.6.0
When trying to run an ARP table report against the Nexus platform, the report fails. The Info Log shows "Unable to find the title line in router ARP table" and then follows with the line "No ARP data...
View ArticleUnable to create destination file: Z:\DOCS\Configuration Files\backup...
Hi,im trying to save my running configurations to a network drive. It seems once i installed cattools as a service, it did not work. However, It did work when i installed catTools as an application....
View ArticleF5.BigIP.TMSH Changes Pending
Whenever I use the F5.BigIP.TMSH Device Type and have CatTools login into a Device I end up with a (Changes Pending) when the device was (In Sync) before. I thought maybe it had something to do with...
View ArticleConnect Failed (errors)
I have some connection problems with some of my devices in my network. I have about 50 Riverbed 250L cashe boxes that I routinely back up each night with a kiwi script. Lately I have been getting...
View ArticleChange default folder destination to another drive
Hello, I have a question abou the installation of kiwi cattools (3.9).Is it possible to install the kiwicattools folder (CatTools3) on the default location (C:\) and change the destination of the...
View ArticleBackup Cisco WLC 5508 8.0
i've been looking all morning for a good way to backup my two WLCs using cat tools. I've never dug into how to use cattools more than just basic devcie config backups on my switches, routers, etc. on...
View ArticleBrocade 6430 switch - Kiwi CatTools - Did not receive command prompt after...
I can't figure out why this isn't working:Scenario:SSH is configured on switch and works via SecureCRTIn Kiwi, SSH username and password is filled in.Intital login requires username/password is...
View Articlefailed to determine hostname - Dell PowerConnect M6220
Hi,When trying to backup the running config on a Dell PowerConnect M6220 switch, I receive the "Failed to determine hostname -timeout" error. This switch is in a Dell M1000e blade chassis. I am using...
View ArticleCannot write to log file
I am using the evaluation version but cannot get log messages from our routers to write to the specified log file or the display. I can write to the display and log when using the test option. In the...
View ArticleCattools, enable mode adtran netvanta
I can't get cattools to enter into enalbe mode on my netvanta 5505 router. VTY access is fine, is "waiting for enable mode". Never mind. Just used a cisco router 2600 and it work fine.
View ArticleCat Tools alternate command
I have setup a device.backup.running config and that is working ok. When I add the use alternate command for a cisco router and use the "show ip arp" command the process just hangs and comes back with...
View ArticleDevice.Backup.Running Config not comparing files
I have been running CatTools 3.4 Free on an XP machine for some time and found it brilliant.I've recently replaced this machine with a Win 7 x64 machine and installed CatTools 3.6 Free. Everything is...
View ArticleWLC 2106 Connection Refused
I am using cattools 3.6 Enterprise. Activity type Device backup TFTP, options running-config. The WLC 2106 is running code 7.0.116.0 and was working until early last month. When it runs i recieve this...
View ArticleScript for HP/H3C Switches
Hi! I'm trying to backup the config of our new HP (H3C) Switches (5120, 5800, 10500). The script I created out of the Custom.Template is not working. The prompt of the switches is "<SWITCHNAME>",...
View ArticleConfiguring Cisco Nexus 7k in Kiwi Cat Tools
I've been able to use Kiwi Cat Tools to backup nearly all of our Cisco devices successfully. However, our Nexus 7k's do not seem to be working with Cat Tools. We use radius authentication and ssh to...
View ArticleCATTOOLS CLI.Send Commands on Juniper EX replies Command is invalid
Hello there, I want to send some show commands via CATTOOLS to some Juniper EX-Switch.However, I constantly get "Command is invalid". Entering the commands (directly) in a ssh session I can proove,...
View ArticleBackup APC SmartUPS Network Management Card Config
Hi!Is there a chance that CatTools could retrieve the config.ini of a APC SmartUPS AP9617/AP9630 Network Management Card using FTP? It would be great if someone of the development team could have a...
View ArticleBacking up a PFSense Firewall over SSH using Generic.Device
Hi chaps, I'm struggling a little to get the Generic.Device with Variations to work correctly when trying to back up my PFSense Firewall. Here is the contents of my variations file:...
View ArticleBackup HP V1910 (Legacy 3Com 2928) switch
I am trying to backup this switch using the Device.CLI.Send activity. Here is what I am trying to send:Login authentication Username:xxxxPassword:<Raben Tire IT Switch>_cmdline-mode onAll...
View Article